General contracting · Canada

FLHA for kitchen renovation

By Safety PaperworkBuilt from provincial OHS law and CCOHS guidance · How we write and check theseUpdated November 9, 2026

Provincial OHS law requires hazards to be assessed and controlled before work starts. A field level hazard assessment (FLHA) for kitchen renovation is done on site at the start of the shift and again whenever conditions change.

It lists the tasks, hazards and controls, and every worker signs on before starting and signs off at the end of the shift. The main hazards are silica dust from concrete, brick, stone and tiles, disturbing asbestos, electric shock from live wiring and lifting and carrying heavy loads.

Make this FLHA now Word template PDF

FLHA example: kitchen renovation

This is a complete FLHA for kitchen renovation, with 5 job steps. Open it in the builder to add your site, crew and signatures, change anything, and download a PDF. Or download the free Word template below and fill it in by hand.

Field Level Hazard Assessment (FLHA)

Kitchen renovation · General contracting · Example

Document FLHA-001 · Rev 1

Job steps, hazards and controls

#	Job step	Hazards	Risk before	Controls	Risk after
1	Check for asbestos and isolate power, gas and water	Disturbing asbestos Electric shock from live wiring Gas and fuel lines	Critical	Get an asbestos survey before work on buildings built before 1990. Elimination Seal off the work area and keep everyone else out. Engineering (guarding) If asbestos must be disturbed, keep it wet, use hand tools not power tools, and clean up with a HEPA vacuum. Engineering Follow your province's asbestos rules, including notification and trained or certified workers where required. Administrative In BC, a qualified person must inspect and write a hazardous materials report before demolition or renovation, and asbestos abatement must be done by a WorkSafeBC licensed contractor (since 1 January 2024). Administrative Stop work straight away if you find suspect asbestos. Do not touch it and tell your supervisor. Administrative Wear a fit-tested respirator suited to the work, and disposable coveralls. PPE Isolate the power before any work. Do not work live. Elimination Lock out and tag the isolation point with your own personal lock and danger tag. Engineering (guarding) Test before you touch: prove dead at the point of work with a tested voltage tester. Engineering Only licensed electricians do electrical work, to the Canadian Electrical Code and provincial rules. Administrative Check for back feeds from solar, batteries and generators that can keep a circuit live after the main switch is off. Administrative Isolate and purge the line before work, with the owner's approval. Elimination Lock off and tag the isolation valve. Engineering (guarding) Check for leaks with a gas detector before and during work, and ventilate the area. Engineering Only licensed gas fitters work on gas lines. Administrative Remove ignition sources: no smoking, no hot work and no sparking tools near the line. Administrative	Medium
2	Remove old cabinets and appliances with two people	Lifting and carrying heavy loads Cuts from sharp edges	High	Plan to avoid carrying: have materials delivered, and old items picked up, as close as possible to where they are used. Elimination Use lighter or smaller loads: order smaller bags and shorter lengths, and drain or break down old items before moving them. Substitution Use trolleys, pallet jacks, hoists, vacuum lifters or equipment instead of carrying by hand. Engineering Use a two-person lift for anything heavy, long or awkward. Plan the route first and clear it. Administrative Keep the load close, back straight and no twisting. Turn with your feet. Administrative Rotate tasks and take breaks on long lifting jobs. Administrative Wear gloves for grip and safety boots to protect your feet. PPE Deburr or cover sharp edges, and fit edge protectors on exposed sheet metal. Engineering Use knives with retractable or self-retracting blades. Engineering Cut away from your body and keep your other hand clear. Administrative Put used blades in a blade bin or sharps container. Administrative Use two people to handle large sheets of metal or glass. Administrative Wear cut-resistant gloves and long sleeves. PPE	Medium
3	Patch walls and run new services	General dust Electric shock from live wiring	Critical	Use low-dust products, such as dust-reduced or pre-mixed compounds. Substitution Seal off the work area with plastic sheeting in occupied buildings. Engineering (guarding) Use tools with dust extraction and a vacuum for clean up. Engineering Lightly mist the area with water to keep dust down, away from anything electrical. Engineering Never dry sweep or blow dust off with compressed air. Administrative Wear a dust mask and safety glasses. PPE If energized work cannot be avoided, use a permit, a safety observer and insulated tools, following CSA Z462. Administrative Wear insulated gloves, arc-rated clothing and a face shield when testing or working near live parts. PPE Electric shock from live wiring: see step 1 for the full controls Administrative	Medium
4	Install cabinets and benchtops, wet cutting stone	Silica dust from concrete, brick, stone and tiles Lifting and carrying heavy loads Saw cuts and kickback	Critical	Order materials cut to size, or use low-dust methods such as score and snap or a block splitter. Substitution Cut outdoors or in a separate area, with other people well away and upwind. Engineering (guarding) Use water on the blade or on-tool dust extraction connected to a HEPA vacuum. Engineering Clean up with a vacuum or wet methods. Never dry sweep or use compressed air. Administrative Have a silica exposure control plan where your province requires one. Administrative Wear a fit-tested N95 (or better) respirator. PPE Lifting and carrying heavy loads: see step 2 for the full controls Administrative Keep blade guards fitted and working, and use the riving knife on table saws. Engineering Use push sticks and clamps, and support long pieces so they do not pinch the blade. Engineering Use a sharp, undamaged blade made for the material. Administrative Stand to one side of the blade line, out of the kickback path. Administrative Let the blade stop fully before reaching in or putting the saw down. Administrative	Medium
5	Fit off, test gas and power, and clean up	Gas and fuel lines Electric shock from live wiring Poor housekeeping and waste	Critical	Know where the shut-off valve is and what to do if a leak happens. Administrative Wear safety glasses and gloves, and keep a fire extinguisher close by. PPE Gas and fuel lines: see step 1 for the full controls Administrative Electric shock from live wiring: see step 1 for the full controls Administrative Order materials to size and send packaging back where you can. Elimination Put waste bins and chutes close to the work. Engineering Clean as you go, and do a full clean up at the end of each day. Administrative Keep exits, stairs and walkways clear at all times. Administrative Stack materials neatly on level ground, away from edges. Administrative	Medium

PPE

CSA green triangle safety boots (CSA Z195)Safety glasses (CSA Z94.3)N95 respiratorHearing protectionWork glovesRespirator fit tested to CSA Z94.4 (P100 for dust, or the type the air test calls for)CoverallsCut-resistant gloves

Plant and equipment

Power drillCircular sawRotary hammerHEPA vacuumHand tools

Emergency

Call 911. Add the nearest hospital, the muster point and the first aid attendant for your site.

Sign-off

Supervisor and every worker sign to confirm they have read and understood this FLHA, then sign off at the end of the shift.

Free FLHA template for kitchen renovation

Word (.docx) and PDF, Letter landscape, no email needed. Fill in your site details, then print or send it.

Word template (.docx)PDF template

Make yours in 2 minutes

Same document, filled in for your job. Answer a few yes or no questions, the crew signs on the phone, and you send the PDF.

Start this FLHA

Pre-start checklist for kitchen renovation

Tick these off before work starts. They come from the hazards, permits and equipment in this job.

FLHA read, explained and signed by everyone on the job
Asbestos register or survey checked for the work area
Water suppression or on-tool extraction fitted; respirators fit tested
First aid attendant, first aid kit and emergency number (911) confirmed
PPE checked and worn: CSA green triangle safety boots (CSA Z195), safety glasses (CSA Z94.3), N95 respirator, hearing protection

The safe sequence of work

Check for asbestos and isolate power, gas and water
Remove old cabinets and appliances with two people
Patch walls and run new services
Install cabinets and benchtops, wet cutting stone
Fit off, test gas and power, and clean up

Hazards to watch on kitchen renovation

The hazards most specific to this job, and the step where each one comes up.

Step 1, 5Gas and fuel linesDamaging or opening a gas or fuel line causes a leak, fire or explosion.

Step 1Disturbing asbestosBuildings built before 1990 may contain asbestos. Drilling, cutting or breaking it releases fibres that cause cancer years later.

Step 4Saw cuts and kickbackCircular saws, mitre saws and table saws cut fingers and hands or throw material back at the user.

Step 3General dustDust from drywall, joint compound, cement and clean up irritates eyes and lungs and makes it hard to see.

Step 2Cuts from sharp edgesSheet metal, glass, blades, cable tray and offcuts cut hands and arms.

Step 4Silica dust from concrete, brick, stone and tilesCutting, grinding or drilling concrete, brick, stone, tiles or fibre cement makes fine silica dust that causes silicosis and lung cancer.

Highest risk on kitchen renovation: Critical before controls (B), down to Medium after controls (A), on the Canada 5 by 5 risk matrix (likely and fatality becomes unlikely and serious injury).

What changes on your site

This example covers the job itself. Your site may add more. Add controls for any of these that apply (the builder asks you these as yes or no questions):

Could anyone fall 3 metres or more, or fall any distance into machinery, water, a hazardous substance or through an opening?
Will anyone use a ladder or stepladder?
Will anyone work on a roof?
Is there a fragile roof, skylight or clear roof sheet?
Will you use a scaffold or mobile tower?

Why FLHAs get rejected

Prime contractors and COR auditors send documents back for these reasons. This example avoids them, but check yours too.

End of shift boxes already say "None" when the form was signed at the start of the shift.
One FLHA reused for days or weeks, or a "review by" date a month away, when the work and conditions change daily.
No time of assessment and no record of any revision, which Alberta s.7(3) requires.
Workers signed that they "read" it, but nothing shows they took part, which Alberta s.8(1) requires.
Work at height with no fall protection plan where the province requires one, or no written rescue procedure for workers using fall arrest.
Permits or locates required on site but no permit or ticket numbers recorded.
No re-assessment entry after an obvious change such as weather, a new task or a new crew member.

Rules by province for kitchen renovation

Province or territory	Key local rule	Regulator
Ontario	Fall protection (O. Reg. 213/91 s.26) applies at a fall of more than 3 m, more than 1.2 m where the work area is used as a path for a wheelbarrow or similar equipment, and at any height into operating machinery, water or other liquid, a hazardous substance, or through an opening.	Ontario Ministry of Labour, Immigration, Training and Skills Development
British Columbia	Fall protection is required where a fall of 3 m or more may occur (s.11.2). A written fall protection plan is required at 7.5 m or more where there are no permanent guardrails (s.11.3).	WorkSafeBC
Alberta	A hazard assessment must be done before work begins, and before a new work site is built (OHS Code s.7(1)). The results must be written down with the controls (s.7(2)).	Alberta Occupational Health and Safety
Quebec	Guardrails (Safety Code s.2.9.1, as amended by Decret 63-2025) are needed where a worker could fall into liquid or a hazardous substance, onto moving parts or dangerous equipment, 1.2 m or more when using a vehicle, 1.5 m or more when handling a load, and more than 3 m in all other cases.	CNESST (Commission des normes, de l'equite, de la sante et de la securite du travail)
Manitoba	A prime contractor is required whenever more than one employer or self employed person works on the site at the same time (Act s.7).	Manitoba Workplace Safety and Health Branch
Saskatchewan	An occupational health committee is required at 10 or more workers of one employer (Act s.3-22).	Saskatchewan Ministry of Labour Relations and Workplace Safety, OHS Division
Nova Scotia	Workers must be trained in fall protection before using it or working in, supervising or planning work in a fall protection area, with a refresher at least every 3 years (WHSR s.21.19).	Nova Scotia Department of Labour, Skills and Immigration, Safety Branch (OHS)
New Brunswick	Fall protection is needed from 3 m above water or the nearest permanent safe level (Reg 91-191 s.49(1)(a)(i)).	WorkSafeNB
Newfoundland and Labrador	Give written notice to the minister before starting a construction project that will last 30 days or more, with the site, location, type of work and number of workers (Regs s.8).	Government Services, Occupational Health and Safety Division
Prince Edward Island	Fall protection is needed from 3 m above the nearest safe surface or water (Fall Protection Regulations s.2(1)(a)).	Workers Compensation Board of PEI, OHS Division
Yukon	Every employer must do hazard assessments with the committee, representative or workers, and redo them after significant changes or incidents (Regs s.1.03.01).	Yukon Workers' Safety and Compensation Board
Northwest Territories	Fall protection is needed from 3 m, or lower if there is a risk of injury (s.119(1)). Guardrails are needed for falls of 1.2 m to 3 m at permanent work sites (s.119(2)).	Workers' Safety and Compensation Commission (WSCC)
Nunavut	No 911. To reach the RCMP in an emergency, dial your community's first three digits then 1111 (Iqaluit: 979-1111). Put the local fire, ambulance and RCMP numbers on every FLHA.	Workers' Safety and Compensation Commission (WSCC)

Questions

Do I need an FLHA for kitchen renovation?

Who signs the FLHA?

The supervisor and every worker take part in the assessment and sign on before work starts, then sign off at the end of the shift. Review it and re-sign whenever the task or conditions change.

How long do I keep it?

Keep completed hazard assessments for at least 3 years (COR auditors sample the last 12 months). Review this FLHA and re-sign whenever the task, crew or conditions change.

What PPE is needed for kitchen renovation?

Usually CSA green triangle safety boots (CSA Z195), Safety glasses (CSA Z94.3), N95 respirator, Hearing protection, Work gloves, Respirator fit tested to CSA Z94.4 (P100 for dust, or the type the air test calls for), Coveralls, Cut-resistant gloves. The site rules may add more, so check with the general contractor.

More general contracting FLHAs

FLHASite Setup6 steps FLHAHome Addition7 steps FLHABathroom Renovation10 steps FLHAResidential Construction6 steps FLHAShed Construction5 steps FLHAGarden Suite Construction5 steps FLHABuilding Maintenance6 steps

Related jobs in other trades

Excavation and earthworksTrenchingAlso involves gas and fuel lines

Toolbox talks for this job

Toolbox talkOverhead Power Lines Toolbox talkSilica Dust Toolbox talkAsbestos Awareness Toolbox talkCrane and Lifting Safety

Blank FLHA template: free FLHA templates. Also for other countries: Australia (SWMS) · United Kingdom (RAMS) · United States (JHA)