General contracting · United States

JHA for bathroom remodel

By Safety PaperworkBuilt from OSHA standards and guidance · How we write and check theseUpdated November 9, 2026

OSHA expects employers to find and control hazards on every job, and many general contractors require a written JHA for bathroom remodel before you start.

A JHA breaks the job into steps, lists the hazards in each step and the controls that protect the crew, and the crew signs it. The main hazards are silica dust from concrete, brick, stone and tiles, disturbing asbestos, electric shock from live wiring and fire from hot works.

Make this JHA now Word template PDF

JHA example: bathroom remodel

This is a complete JHA for bathroom remodel, with 10 job steps. Open it in the builder to add your site, crew and signatures, change anything, and download a PDF. Or download the free Word template below and fill it in by hand.

Job Hazard Analysis (JHA)

Bathroom renovation · General contracting · Example

Document JHA-001 · Rev 1

Job steps, hazards and controls

#	Job step	Hazards	Risk before	Controls	Risk after
1	Check the asbestos survey; older wet areas often have asbestos sheeting	Disturbing asbestos	Critical	Treat insulation, surfacing and resilient flooring in buildings built before 1981 as asbestos unless testing shows otherwise, and get the owner's asbestos survey before you start. Elimination Seal off the work area and keep everyone else out. Engineering (guarding) If asbestos must be disturbed, keep it wet, use hand tools not power tools, and clean up with a HEPA vacuum. Engineering Follow 29 CFR 1926.1101: competent person, work class, regulated area and exposure monitoring. Administrative Commercial renovation and any demolition need a NESHAP asbestos inspection first, and demolition needs written notice to the state or EPA 10 working days before work starts (40 CFR 61 Subpart M). Administrative Roofing felts, cement shingles and siding, roof coatings and old panel backboards can also contain asbestos. Test them or treat them as asbestos; asbestos roofing is removed intact with hand tools by trained workers (29 CFR 1926.1101(g)(8)). Administrative Stop work straight away if you find suspect asbestos. Do not touch it and tell your supervisor. Administrative Wear a fit-tested NIOSH-approved respirator suited to the work class, and disposable coveralls. PPE	Medium
2	Separate the work area from occupants with dust screens and keep a toilet available	Working in an occupied home or building General dust	Medium	Plan noisy, dusty or risky work for when the building is empty. Elimination Close off the work area with barriers, plastic sheeting or locked doors, and put up signs. Engineering (guarding) Keep fire exits and paths clear at all times. Administrative Tell occupants before you turn off power, water or gas, and before noisy or dusty work. Administrative Lock away tools, chemicals and materials each day, out of reach of children. Administrative Clean up dust and debris at the end of each day. Administrative Use low-dust products, such as dust-reduced or pre-mixed compounds. Substitution Seal off the work area with plastic sheeting in occupied buildings. Engineering (guarding) Use tools with dust extraction and a vacuum for clean up. Engineering Lightly mist the area with water to keep dust down, away from anything electrical. Engineering Never dry sweep or blow dust off with compressed air. Administrative Wear a dust mask and safety glasses. PPE	Low
3	Isolate water and power to the room, apply lockout/tagout	Electric shock from live wiring Stored energy	Critical	Isolate the power before any work. Do not work live. Elimination Lock out and tag the disconnecting means with your own personal lock and tag so the circuit cannot be energized (29 CFR 1926.417). Engineering (guarding) Test before you touch: prove dead at the point of work with a tested voltage tester. Engineering Only qualified persons work on or near exposed energized parts. Administrative Check for back feeds from solar, batteries and generators that can keep a circuit live after the main switch is off. Administrative If energized work cannot be avoided, use an energized work permit, a safety observer and insulated tools, following NFPA 70E. Administrative Wear insulated gloves, arc-rated clothing and a face shield when testing or working near live parts. PPE Release or block all stored energy before work: release the pressure in pipes, tanks and hoses, bleed hydraulics, release springs, lower loads. Elimination Lock out and tag all energy sources with personal locks. Engineering (guarding) Put mechanical blocks or props under raised parts like buckets, tipper bodies and doors. Engineering Test that the system is dead and nothing can move before you start. Administrative Follow the maker's procedure, for example for garage door and roller door springs. Administrative Wear safety glasses and gloves. PPE	Medium
4	Remove fixtures, the toilet and glass shower screens carefully	Glass handling and breakage Lifting and carrying heavy loads Sewage and wastewater	High	Use suction lifters, glass trolleys or a glazing robot for large panes. Engineering Store glass upright on racks and secure it. Never lay it flat or lean it loosely. Engineering Use two or more people for large panes, and clear the carry route first. Administrative Mark new glass with tape or stickers so nobody walks into it. Administrative Clean up broken glass straight away into a marked container. Administrative Plan to avoid carrying: have materials delivered, and old items picked up, as close as possible to where they are used. Elimination Use lighter or smaller loads: order smaller bags and shorter lengths, and drain or break down old items before moving them. Substitution Lifting and carrying heavy loads: see step 8 for the full controls Administrative Flush and drain the line before opening it, and plan the job to avoid contact. Elimination Use drain cameras, jetters and long-handled tools to keep hands out. Engineering Cover cuts with waterproof dressings. Never eat, drink or smoke before washing. Administrative Wash hands well and clean tools and boots after the job. Administrative Keep vaccinations such as tetanus and hepatitis A up to date, on medical advice. Administrative	Medium
5	Strip tiles and linings with dust control	Silica dust from concrete, brick, stone and tiles Loud noise Hand-arm and whole-body vibration	Critical	Order materials cut to size, or use low-dust methods such as score and snap or a block splitter. Substitution Cut outdoors or in a separate area, with other people well away and upwind. Engineering (guarding) Use wet cutting or on-tool dust collection with a HEPA vacuum, as set out in Table 1 of 29 CFR 1926.1153. Engineering Clean up with a vacuum or wet methods. Never dry sweep or use compressed air. Administrative Have a written exposure control plan and a competent person for silica (29 CFR 1926.1153). Administrative Workers who must wear a respirator 30 or more days a year get a free medical exam every 3 years (29 CFR 1926.1153(h)). Administrative Wear the respirator Table 1 lists for the task: APF 10 (a fit-tested N95 or half mask) for most tasks, APF 25 (such as a loose-fitting PAPR) for tuckpointing with a handheld grinder for more than 4 hours a shift. PPE Use quieter tools and methods, such as cut-to-size materials, low-noise machines and battery tools. Substitution Keep noisy plant away from work areas, and use screens or distance between the noise and people. Engineering (guarding) Keep tools maintained and use mufflers on compressors and generators. Engineering Limit time on noisy tools and rotate workers. Administrative If you have to shout to be heard at arm's length, wear hearing protection. Administrative Use low-vibration tools and methods, such as a breaker on an excavator instead of a hand jackhammer. Substitution Keep tools sharp and well maintained, and use anti-vibration handles and seats. Engineering Limit trigger time on high-vibration tools and rotate workers. Administrative Keep hands warm and dry, and take regular breaks. Administrative Report tingling, numbness or white fingers early. Administrative	Medium
6	Check for mould, rot and damaged framing once linings are off	Mold and droppings Structural collapse during alterations	High	Fix the water leak and dry the area before removing mold. Elimination Seal off the area with plastic sheeting and keep occupants out. Engineering (guarding) Clean up with a HEPA vacuum and wet wipes. Never dry sweep. Engineering Bag moldy material on site and remove it promptly. Administrative Wash hands and face before eating and at the end of each shift. Administrative Wear an N95 (or better) respirator, gloves, goggles and disposable coveralls. PPE Get an engineer to check before removing any wall, beam, post or bracing that may be load-bearing. Elimination Keep everyone clear of the area under and next to the work. Engineering (guarding) Install temporary props, needles or shoring as designed before removing any support. Engineering Follow the engineer's sequence. Do not change it without approval. Administrative Check props daily. Do not remove them until the permanent support is in and approved. Administrative Wear a hard hat and safety boots. PPE	Medium
7	Rough in plumbing and electrical by licensed trades	Electric shock from live wiring Fire from hot works	Critical	Electric shock from live wiring: see step 3 for the full controls Administrative Use cold work methods where you can, such as bolting, press fittings or cutting with a saw instead of a torch. Elimination Move anything that can burn at least 35 feet away, or cover it with fire blankets. Engineering (guarding) Use fire-resistant screens to stop sparks reaching people or gaps in walls and floors. Engineering Get a hot work permit before starting. Administrative Keep a charged fire extinguisher and fire blanket at the work spot. Administrative Keep a fire watch during the work and for at least 60 minutes after you finish (NFPA 51B), longer if the permit says so. Administrative Check for smoldering behind walls, in ceilings and under floors before you leave. Administrative Wear flame-resistant clothing, welding gloves and eye or face protection. PPE	Medium
8	Sheet and waterproof with good ventilation	Hazardous chemicals Lifting and carrying heavy loads	High	Choose the least harmful product that does the job, for example water-based instead of solvent-based. Substitution Use chemicals in well-ventilated areas, or use fans and extraction in closed rooms. Engineering Read the Safety Data Sheet (SDS) and labels before use, following OSHA Hazard Communication. Administrative Keep chemicals in labeled containers. Never pour them into drink bottles. Administrative Store chemicals away from heat, food and drink, and keep products that react with each other apart. Administrative Have eye wash and a spill kit nearby, and wash hands before eating. Administrative Wear chemical-resistant gloves and safety glasses or goggles as listed on the SDS. PPE Use a respirator with the right cartridge if the SDS calls for one. PPE Plan to avoid carrying: have materials delivered, and old items picked up, as close as possible to where they are used. Elimination Use lighter or smaller loads: order smaller bags and shorter lengths, and drain or break down old items before moving them. Substitution Use trolleys, pallet jacks, hoists, vacuum lifters or plant instead of carrying by hand. Engineering Use a two-person lift for anything heavy, long or awkward. Plan the route first and clear it. Administrative Keep the load close, back straight and no twisting. Turn with your feet. Administrative Rotate tasks and take breaks on long lifting jobs. Administrative Wear gloves for grip and safety boots to protect your feet. PPE	Medium
9	Tile, cutting wet	Silica dust from concrete, brick, stone and tiles Saw cuts and kickback Repetitive work and awkward postures	Critical	Silica dust from concrete, brick, stone and tiles: see step 5 for the full controls Administrative Keep blade guards fitted and working, and use the riving knife on table saws. Engineering Use push sticks and clamps, and support long pieces so they do not pinch the blade. Engineering Use a sharp, undamaged blade made for the material. Administrative Stand to one side of the blade line, out of the kickback path. Administrative Let the blade stop fully before reaching in or putting the saw down. Administrative Use tools that cut the effort: powered screwdrivers, long-handled tools and extension poles for overhead work. Substitution Set work up at waist height on benches or trestles where you can. Engineering Use light tools with good grips, and keep blades and bits sharp. Engineering Rotate tasks and take short breaks every hour on repetitive work. Administrative Warm up before heavy physical work and report aches and pains early. Administrative	Medium
10	Fit off fixtures, test and clean up	Slips and trips Poor housekeeping and waste	Medium	Plan walkways and keep them clear of materials, hoses and leads. Elimination Run cords and hoses overhead on hooks or stands, or along walls, not across walkways. Engineering Fill or cover holes, and lay boards or mats on muddy access paths. Engineering Clean up offcuts, packaging and spills as you go, not at the end of the day. Administrative Keep work areas, stairs and access paths well lit. Administrative Wear safety boots with good grip, laced up. PPE Order materials to size and send packaging back where you can. Elimination Put dumpsters and waste chutes close to the work. Engineering Clean as you go, and do a full clean up at the end of each day. Administrative Keep exits, stairs and walkways clear at all times. Administrative Stack materials neatly on level ground, away from edges. Administrative Wear gloves when handling waste. PPE	Low

PPE

Safety-toe boots (ASTM F2413)Safety glasses (ANSI Z87.1)N95 respiratorHearing protection (earmuffs or plugs)Cut-resistant glovesKnee padsHalf-face respirator (P100 cartridges)CoverallsWork glovesChemical-resistant glovesSafety goggles (ANSI Z87.1)Face shield (ANSI Z87.1)Welding gloves

Plant and equipment

JackhammerWet tile sawPower drillHEPA vacuumHand tools

Permits and plans

Lockout/tagout (1926.417)Hot work permit (fire watch at least 60 minutes after, NFPA 51B)

Emergency

Call 911. Add the nearest hospital, the assembly point and the first aid / cpr person for your site.

Sign-off

Supervisor and every worker sign to confirm they have read and understood this JHA.

Free JHA template for bathroom remodel

Word (.docx) and PDF, Letter landscape, no email needed. Fill in your site details, then print or send it.

Word template (.docx)PDF template

Make yours in 2 minutes

Same document, filled in for your job. Answer a few yes or no questions, the crew signs on the phone, and you send the PDF.

Start this JHA

Pre-start checklist for bathroom remodel

Tick these off before work starts. They come from the hazards, permits and equipment in this job.

JHA read, explained and signed by everyone on the job
Lockout, tagout and test before touch done before work starts
Asbestos register or survey checked for the work area
Water suppression or on-tool extraction fitted; respirators fit tested
Hot work permit issued, extinguisher at hand, fire watch arranged
First aid / CPR person, first aid kit and emergency number (911) confirmed
PPE checked and worn: safety-toe boots (ASTM F2413), safety glasses (ANSI Z87.1), N95 respirator, hearing protection (earmuffs or plugs)

The safe sequence of work

Check the asbestos survey; older wet areas often have asbestos sheeting
Separate the work area from occupants with dust screens and keep a toilet available
Isolate water and power to the room, apply lockout/tagout
Remove fixtures, the toilet and glass shower screens carefully
Strip tiles and linings with dust control
Check for mould, rot and damaged framing once linings are off
Rough in plumbing and electrical by licensed trades
Sheet and waterproof with good ventilation
Tile, cutting wet
Fit off fixtures, test and clean up

Hazards to watch on bathroom remodel

The hazards most specific to this job, and the step where each one comes up.

Step 6Mold and droppingsWater-damaged buildings, bird and rat droppings and dead animals hold mold and germs that cause breathing problems and infections.

Step 4Sewage and wastewaterContact with sewage spreads germs that cause stomach illness, hepatitis and skin infections.

Step 4Glass handling and breakageGlass panes break while being moved or fitted, causing deep cuts, or heavy panels fall and crush.

Step 3Stored energyEnergy left in springs, hydraulics, compressed gas, raised loads or capacitors releases suddenly and crushes or injures workers.

Step 7Fire from hot worksSparks and heat from welding, grinding or flame torches set fire to timber, insulation, rubbish or fuel nearby.

Step 2Working in an occupied home or buildingResidents, staff or children wander into the work area and get hurt, or the work blocks exits or cuts off power or water while people are inside.

Highest risk on bathroom remodel: Critical before controls (B), down to Medium after controls (A), on the United States 5 by 5 risk matrix (likely and fatality becomes unlikely and serious injury).

What changes on your site

This example covers the job itself. Your site may add more. Add controls for any of these that apply (the builder asks you these as yes or no questions):

Will anyone work 6 feet or more above a lower level?
Will anyone use a ladder or stepladder?
Will anyone work on a roof?
Is there a skylight, fiberglass panel or other fragile roofing?
Will you use a scaffold or rolling tower?

Why JHAs get rejected

General contractors send documents back for these reasons. This example avoids them, but check yours too.

Generic steps such as "work safely" or "use PPE" with no task-specific hazards or controls.
No OSHA standards referenced for the hazards that have them, such as fall protection, ladders, scaffolds or silica.
No competent person named for fall protection, excavation, scaffolds or silica where those hazards exist.
Equipment listed without inspection requirements, and no training listed for the people using it.
Respirators listed with no respiratory protection program, medical clearance or fit test.
Controls rely only on PPE when engineering controls such as guardrails, wet cutting or extraction are feasible.
No crew sign-off, or no date and revision when the job has changed.

Questions

Do I need a JHA for bathroom remodel?

OSHA expects employers to find and control hazards on every job, and many general contractors require a written JHA for bathroom remodel before you start.

Who signs the JHA?

The supervisor or competent person who prepared it signs, and every crew member signs to show they were trained on the hazards and controls before the job starts. Many general contractors also sign to accept it.

How long do I keep it?

Keep this JHA on site during the job, and keep it with the training and inspection records for at least 1 year after the job (longer if your state plan or general contractor requires it). OSHA does not set a retention period for JHAs themselves.

What PPE is needed for bathroom remodel?

Usually Safety-toe boots (ASTM F2413), Safety glasses (ANSI Z87.1), N95 respirator, Hearing protection (earmuffs or plugs), Cut-resistant gloves, Knee pads, Half-face respirator (P100 cartridges), Coveralls, Work gloves, Chemical-resistant gloves, Safety goggles (ANSI Z87.1), Face shield (ANSI Z87.1), Welding gloves. The site rules may add more, so check with the general contractor.

More general contracting JHAs

JHASite Mobilization6 steps JHAHome Addition7 steps JHAKitchen Remodel5 steps JHAResidential Construction6 steps JHAGarage Construction5 steps JHAADU Construction5 steps JHABuilding Maintenance6 steps

Related jobs in other trades

ElectricalElectrical Panel UpgradeAlso involves working in an occupied home or building ConcretingConcrete Slab PourAlso involves hand-arm and whole-body vibration PaintingLead Paint Removal (RRP)Also involves working in an occupied home or building DrywallDrywall InstallationAlso involves electric shock from live wiring RoofingRoof ReplacementAlso involves disturbing asbestos Excavation and earthworksTrenching and ExcavationAlso involves hand-arm and whole-body vibration

Toolbox talks for this job

Toolbox talkWorking at Heights Toolbox talkSilica Dust Toolbox talkAsbestos Awareness Toolbox talkManual Handling and Back Safety

Blank JHA template: free JHA templates. Also for other countries: Australia (SWMS) · United Kingdom (RAMS) · Canada (FLHA)